Create handles

Handles are created by adding a @Handle annotation to an attribute.

Model with @Handle annotation added

The above handles were created using the following attribute annotations:

@Handle(shape=Cube, axis=y)
attr height = 30

@Handle(shape=Cube, axis=x)
attr width = 30

@Handle(shape=Cube, axis=z)
attr depth = 30

Lot -->
	s(width, 0, depth)
	extrude(height)
	Cube

The option shape=Cube attaches the handle to the shape Cube. The option axis=x|y|z specifies a scope direction for the handle. Thin gray extension lines connect the handle to the shape that it is measuring. Handles can be applied to a wide range of objects.

Tree model with handle

The above handle was created using the annotation:

@Handle(shape=TreeCenter, axis=y, reference=center, slip=screen)
attr height = 30

Handles that do not move with the camera can also be created, for example:

@Handle(shape=TreeCenter, axis=y, reference=origin, slip=inside, occlusion=false)
attr height = 30

The advanced options reference and slip specify the handle's position and movement as the camera moves. In this case the height handle rotates smoothly around the tree with the camera.

Note:

Adding many handles, or adding handles to complex models may lead to low framerates on low-end hardware.

General options

The default options in the below table are marked with an asterisk. If any option is omitted, the default value is taken. The only option that must be specified is shape.

shape

shape=shape_name^argument_count

Selects the shape of the rule with name shape_name. The parameter argument_count specifies the number of arguments that the rule takes.

If ^argument_count is omitted, ^0 is assumed. An * allows referencing anonymous leaf shapes, e.g.: shape=Box*^3.

 

type
type=linear*|move|angular|toggle|selector|color
Selects the type of handle to create. , and color for editing color string attributes.
Additional options specific to each type are given below:
type=linear Handles with a linear type are used for editing float values that represent distances.
type=move The move type is used for editing float values that represent positions, in contrast to the linear type the handles are always shown at a constant length.
type=angular The angular type is for float attributes that represent angles.
type=toggle The toggle type is for boolean attributes.
type=selector The selector type is for attributes with the @Enum annotation.
type=color The color type is for editing color string attributes.

 

align
align=topLeft|left|bottomLeft|bottom|bottomRight|right|topRight|top|default*
Selects a screen direction as the offset direction preference for a reference handle. default selects the nearest location outside of the model's silhouette.
linear example of align=left
linear example of align=right
toggle example of align=topLeft
toggle example of align=right

 

slip
slip=scope*|screen|inside
This option specifies the way in which reference handles may be moved outside the model's silhouette. slip=scope moves the handle in directions given by the scope axes, slip=screen moves the handle parallel to the camera, and slip=inside disables the offsetting behvior.
Different slip are appropriate for different shapes. For example, the length of cylindrical objects is best specified using slip=screen, while the dimensions of a cuboid should use slip=scope.
slip=scope causes the handle to align itself to the edges of the scope as the camera moves. In contrast slip=screen maintains a constant offset direction, independent of camera location. It is recommended that cuboid objects use slip=scope, while cylindrical or spherical objects will use slip=screen. While it is possible to use either of these options in any case, following these recommendations presents a consistent and intuitive interface to users.

 

repeat
repeat=chain*|none
Chained handles will be clustered into a single continuous chain. Linear handles of several different attributes with the same orientation may be grouped onto one chain if there is sufficient space.
Left: repeat=chain, right: repeat=none If repeat=none is set, CityEngine determines an appropriate location for a single handle, preferring locations with short extension lines and long linear handles.

 

minDisplaySize

minDisplaySize=pixels

If the size of a handle is below pixels, it is not shown. Users can override this behavior by pressing or control key.

The size of a handle with linear type is the screen-length. The size of an angular handle is the distance between zero degree and the handle. The size of toggle, selector, or color handles is the screen length of the shape's scope's shortest edge.

 

extensionLines
extensionLines=scope*|silhouette|fade|off
Specifies the style of the extension lines associated with a handle.
Clockwise from bottom right: extensionLines=scope, extensionLines=fade, extensionLines=off and extensionLines=silhouette.
The image below shows typical use cases for the different extension line types. scope (left) is used to highlight embedded features, silhouette (middle) with obvious features to avoid cluttering the geometry and fade (right) for irregular shapes.

 

translate

translate={translate_x,translate_y,translate_z}

Specifies a scope-relative translation of the handle. For example, translate={3,0,0} translates the handle by 3 * scope.sx in the direction of the scope's x axis.

 

occlusion

occlusion=true*|false

Enables or disables occlusion handling for the handle. When enabled handles are only shown when their reference positions are visible. However, for complex models this may cause the handle to flicker. Using occlusion=false will resolve this issue, and never hide the handle because of occlusion.

 

color
color=hexCodeString
Normally the color of handles is given by the viewport hightlight color. color allows users to override this behavior with a preferred color hexCodeString is specified as an RGB hex code string within quotes, for example color="#FF0000".
The vertical linear handle uses the parameter color="#FFF00", the horizontal linear handle color="#33FF33", the selector handle color="#FF0000" and the toggle handle color="#33FFFF".

Linear type options

Linear handles are assumed to be associated with a scope edge. The length of the linear handle is given by the scope edge specified by axis.

reference
reference=edges*|center|origin|radial
Specifies the location of the reference handles. Note: The location of radial handles depends on the camera position.
Handles are moved to their offset position using the direction given by the slip option.
reference=edges Typical use cases are boxes or cuboid geometries (as shown in the first example on this page).
reference=center Suitable for the length of cylindrical or spherical objects (such as the tree's height in the second example of this page).
reference=origin Used when a feature is one dimensional or when the exact position of a handle must be specified. The shape's origin is at the right of the cube.
reference=radial Can be used for the width of cylindrical objects (such as the dead tree model above).

 

axis

axis=y*|x|z|x-|y-|z-

The linear handle is positioned along the specified scope axis of the shape.

 

skin
skin=doubleArrow*|singleArrow|diameterArrow|sphere|hemisphere
Linear handles have several options for the rendering of terminators. These options do no change the behavior of the handle, with the exception of skin=diameterArrow, which scales symmetrically about its center when dragged.
skin=doubleArrow
skin=singleArrow
skin=diameterArrow
skin=sphere
skin=hemisphere

Move type options

Move handles are similar to linear handles, and are also associated with a scope edge. However, the length of the move handle is always constant, in contrast to linear handles where it is given by the scope edge. When dragging one end of the handle, the other end also moves by the same amount. This makes them suitable for attributes representing positions or offsets.

axis and skin are similar to linear handles. For reference, only center and origin is supported. Also, the slip value is restricted to inside.

Angular type options

Angular handles allow the user to manipulate angles. Typically a combination of axis and translate are used to position the handle in the appropriate location. By default, angular handles do not offset themselves (slip=inside). This behavior can be altered by specifying another slip value.

reference
reference=edges|center*|origin
Specifies the location of the reference handles. In the below images, the shape origin is in the bottom right of the screen.
reference=edges
reference=center
reference=origin

 

axis
axis=y*|x|z|x-|y-|z-
Selects the rotation scope axis.. A negative axis reverses the direction of rotation.
The red, green and blue lines are the x, y and z axes. For example axis=x rotates around the x axis towards the z axis. The angular handles each have an attribute value of 30 degrees

 

skin
skin=doubleArrow*|ring
Rotational handles have two skin options: doubleArrow or ring.
skin=doubleArrow
skin=ring

Toggle, Selector and Color Type Options

Toggle, selector and color types share layout options.

reference
reference=edges|center*|origin|radial
Specifies the location of the reference handles. In the below images, the shape origin is in the bottom right of the screen. Note: The location of radial handles depends on the camera position.
reference=edges
reference=center
reference=origin
reference=radial

axis

if slip=scope
axis=x|y*|z|xy|xz|yz
Specifies the directions in which the handle may move when slip=scope is set. For example, handles with the option axis=xy may move along the x or y axes.
Left: the reference position for the toggle handle at the origin, and the three axes. Middle: axis=x, the handle can move alone the x axis. Right: axis=xy, the handle can move along the x or the y axis to find the best location.

 

if slip=screen

axis=x|y*|z

In the case of slip=screen the handle moves in the same manner as a linear handle with the same axis parameter.

 

if slip=inside

axis does not affect the placement of the handle if slip=inside.