Skip To Content

Use high-accuracy GPS

If you are using a high-accuracy receiver, you need to configure Collector to work with it. Connect your receiver to your device, and then in Collector, select the receiver, create a location profile, and specify your desired accuracy. You can also configure Collector to do GPS averaging during your collections.

Connect your receiver to your device

Collector supports receivers integrated into devices, as well as external receivers connected to devices via Bluetooth. If your receiver is integrated into the device, proceed to the next section, Select your receiver in Collector. If you are using an external receiver, follow these steps to connect it to your device:

  1. Verify that your GPS receiver is compatible with Collector.

    Your receiver must support the output of NMEA sentences. Check your receiver's user manual to see if it does. If it does but isn't already configured to do so, the user manual should also have instructions on how to configure the receiver to output NMEA sentences. These instructions need to be completed before connecting the receiver to Collector.

  2. Turn on your receiver and place it near your device.

    Go to your device's Bluetooth settings and view Available devices. Wait for your receiver's name to appear in the list.

    Tip:

    If your Bluetooth receiver doesn't appear in the list, make sure it isn't connected to another device. To disconnect your receiver from another device, in the device's Bluetooth settings, select the settings icon next to the receiver, and select Unpair or Forget.

  3. Select the receiver's name in Available devices to pair it with your device.

Select your receiver in Collector

Once your GPS receiver is connected to your device, specify that you want the receiver to provide GPS locations in Collector. Once a receiver is selected, this is the only source of positions that is used until a new receiver is selected.

  1. After signing in to Collector, from the Map Gallery, select Overflow Overflow and select Settings.
  2. In the Location section, select Location provider.

    The Select a GPS receiver list displays.

  3. If your receiver doesn't appear in the list, add it by taking the following steps:
    1. Select Add a receiver Add a receiver to display a list of paired Bluetooth receivers.
    2. Select your receiver.
    3. If you are mounting the receiver to a pole, enter the antenna height.
    4. Select OK.

    You are returned to the Select a GPS receiver list and your receiver is listed.

  4. Select your receiver.
  5. If you need to change the antenna height, select Overflow Overflow, select Details, enter the antenna height, and press the device's back button.
  6. Select Collector Collector to return to Settings.

Create a location profile in Collector

A location profile defines the coordinate system and, if required, datum transformations to apply when locations are received from your GPS receiver. The location profile applies to both internal and external receivers. It's recommended to create a location profile when you're using a correction service.

  1. In the Settings of Collector, under the Location section, select Location profile and select Add profile Add a location profile.
  2. In the Search box, type the name or ID of your receiver's correction service's geographic coordinate system (GCS) to filter the results in the list, and then select the correction service's GCS.
  3. If your map uses a projected coordinate system, select Projected.
    Caution:

    It is important to make sure the correct filter is selected at the bottom of the screen because some geographic and projected coordinate systems have the same name.

  4. In the Search box, type the name or ID of the map's coordinate system to filter the results in the list, and then select the map's coordinate system.
  5. If a datum transformation between the coordinate systems of your receiver's correction service and your map is available, you are prompted to specify the data collection area. To zoom to your location on the map, select Use My Location Use My Location. Once you have zoomed in to the data collection area, select Continue Continue and select the desired datum transformation from the list of available transformations.
    Note:

    You can only specify the data collection area on the basemap when your device has access to online data via Wi-Fi or a cellular network.

    The datum transformation list is sorted by relevance, with the most relevant transformation based on the data collection area listed first.

    Some transformations such as grid-based transformations are not currently supported.

  6. Select Done.
  7. Provide a name for the location profile and select OK.

    The location profile is added to the Location profiles list.

  8. Select the new location profile from the Location profiles list to set it as your current profile and select Collector Collector to return to Settings.

Specify the required accuracy in Collector

Your organization might require that all data collected meet a specific minimum accuracy. In Collector, you can set the required accuracy of GPS positions to ensure that data you collect meets your organization's data collection standards.

  1. In the Settings of Collector, under the Location section, select Accuracy.
  2. Select the units for the required accuracy.
    Note:

    To change the units of measurement between metric and imperial, in the app's Settings, select the units you want to use in Units of Measurement in the General section.

  3. Enter the required accuracy and select OK.
  4. Select Collector Collector to exit the settings.

Enable GPS averaging

Your organization might require that you collect a number of points for a single location and average their information to get a final location and accuracy. In Collector, you can set the required number of points that have to be averaged to get a single location. Any time you use GPS location in your data collection, the required number of points will be collected and averaged for point features, as well as for the individual vertices of lines and polygons.

Note:

Streaming to collect lines and polygons and GPS averaging are mutually exclusive: you can't average the values and stream at the same time.

To use GPS averaging, enable it in the app's settings. All collections done using the GPS and without streaming will use averaging if it is enabled.

  1. In the Settings of Collector, under the Collection section, enable GPS averaging.
  2. Select Number of locations and provide the number of GPS positions you'd like to average to determine the location and accuracy for your collection. The default is 5 positions. Select OK.

Once GPS averaging is enabled, your data collection using the GPS will do averaging on each point collected. When you start a collection, you'll see a banner showing how many points have been averaged so far, along with the current averaged accuracy. Once a location has been obtained and while averaging is in progress, you'll see a red dot indicating the current averaged position on the map.

GPS averaging in progress

When the number of locations you specified in the setting has been obtained, averaging completes, the banner goes away, and a point is placed on the map. To stop averaging before it completes, select Stop, discarding the averaging you have done so far.

Your receiver is now providing locations to Collector. As you collect data, you will provide your organization with high-accuracy data that meets its standards.